CNC Router: Difference between revisions

← Older edit

CNC Router (view source)

Revision as of 18:05, 21 June 2024

481 bytes added , 10 days ago

no edit summary

Pablof

Confirmed users, fcfl_members

4

edits

Revision as of 02:47, 17 December 2023 (view source) Macakcat (talk \| contribs) (→‎Replacing 3D Printed Dust Collection Boot) ← Older edit		Latest revision as of 18:05, 21 June 2024 (view source) Pablof (talk \| contribs) No edit summary
(7 intermediate revisions by 2 users not shown)
Line 53: [https://drive.google.com/file/d/1hwypOCyQ11mNdx32k812W3lDYDm5G8pF/view?usp=sharing FCFL CAMaster WinCNC post processor for Fusion 360] - "FCFL_CAMaster_wincnc_m3x_171014.cps" with Automatic Tool Changer disabled. [https://drive.google.com/file/d/~~1xINHxkOfhpw8RRROKAxGHJkEOYRJCSro~~1e_epUuee_oOA-Cs6QrRGmAygsFLcqrwy/view?usp=sharing FCFL CNC Router Tool Library for Fusion 360] - Complete tool library ready to import into Fusion 360. This tool library is version ~~2023_03_04~~2024_06_21. (DEPRECATED) [https://docs.google.com/spreadsheets/d/1OWSaMgkcoUyyKQk58nxxpIXn-BqWR1F2R01m_Mm7xRU/edit#gid=0 Old FCFL Bit Inventory] - Old spreadsheet. No longer in use. Line 93: Standard Disclaimers: * Monitor your cnc job at all times * Don't be inebriated▼ * No loose items▼ * Standard safety gear (safety glasses) * Tie back hair ▲* No loose items ▲* Don't be inebriated * Don't be stupid Line 321 ⟶ 322: === Replacing 3D Printed Dust Collection Boot === [[File:Dustboot1.jpg\|thumb\|alt=Dust boot\|FCFL Dust Collection Boot]] NOTE: This file's geometry tolerances need adjustment (boot groove & magnet holes). It may work on some printers and not on others, so be prepared to modify as needed (either physically or digitally). Holes for the M3 retaining pins were an after-mod, so are not included in the file and need to be manually added later. This part can be printed as one piece or as two separate pieces. * Full STL file requires a large printer.: ** [https://drive.google.com/file/d/13Dxwsi6C2WWSWrQ5LSA_VqfQnIbXf5Xv/view?usp=sharing CNC Dust Boot Full.stl] * Separate STL files can be done on any Ultimaker or similar printer.: [https://drive.google.com/file/d/1rEx6f0t3lkniwuvnSYDCObXyN7-Jj_53/view?usp=sharing CNC Dust Boot Half A.stl] [https://drive.google.com/file/d/1wl_y9x7eB8jHbfCK3BMTucW-wmBR_UFu/view?usp=sharing CNC Dust Boot Half B.stl] Line 347 ⟶ 350: # Press in the magnets. The magnets should be about flush and in the same plane as the top surface of the boot. # Glue the magnets in place. # Install the brushes. No glue is needed. Will need to modify to fit. Clamp to press in bristles in place. # Drill holes to allow for M3 retaining "pins" to fit in. == Troubleshooting ==