CNC Router: Difference between revisions
Content deleted Content added
No edit summary |
|||
(19 intermediate revisions by 2 users not shown) | |||
Line 43:
[https://www.wincnc.net/ CAMaster WinCNC] (Machine Controller Software)
[https://
VCarve Pro Makerspace ID:
Line 53:
[https://drive.google.com/file/d/1hwypOCyQ11mNdx32k812W3lDYDm5G8pF/view?usp=sharing FCFL CAMaster WinCNC post processor for Fusion 360] - "FCFL_CAMaster_wincnc_m3x_171014.cps" with Automatic Tool Changer disabled.
[https://drive.google.com/file/d/
(DEPRECATED) [https://docs.google.com/spreadsheets/d/1OWSaMgkcoUyyKQk58nxxpIXn-BqWR1F2R01m_Mm7xRU/edit#gid=0 Old FCFL Bit Inventory] - Old spreadsheet. No longer in use.
Line 93:
Standard Disclaimers:
* Monitor your cnc job at all times
* Don't be inebriated▼
* No loose items▼
* Standard safety gear (safety glasses)
* Tie back hair
▲* No loose items
▲* Don't be inebriated
* Don't be stupid
Line 304 ⟶ 305:
=== Replacing 3D Printed Clamps ===
[[File:FCFL CNC Router Clamp image.png|thumb|alt=FCFL CNC Router Clamp render|FCFL CNC Router Clamp
STL file:
* [https://drive.google.com/file/d/
Print settings:
* Position model on its side (bolt direction horizontal to bed)
* Material: PLA+
* 0.8 nozzle
* 0.2 layer height
Line 317 ⟶ 319:
* Generate support everywhere
* Skirt
=== Replacing 3D Printed Dust Collection Boot ===
[[File:Dustboot1.jpg|thumb|alt=Dust boot|FCFL Dust Collection Boot]]
NOTE: This file's geometry tolerances need adjustment (boot groove & magnet holes). It may work on some printers and not on others, so be prepared to modify as needed (either physically or digitally). Holes for the M3 retaining pins were an after-mod, so are not included in the file and need to be manually added later.
This part can be printed as one piece or as two separate pieces.
* Full STL file requires a large printer:
** [https://drive.google.com/file/d/13Dxwsi6C2WWSWrQ5LSA_VqfQnIbXf5Xv/view?usp=sharing CNC Dust Boot Full.stl]
* Separate STL files can be done on any Ultimaker or similar printer:
** [https://drive.google.com/file/d/1rEx6f0t3lkniwuvnSYDCObXyN7-Jj_53/view?usp=sharing CNC Dust Boot Half A.stl]
** [https://drive.google.com/file/d/1wl_y9x7eB8jHbfCK3BMTucW-wmBR_UFu/view?usp=sharing CNC Dust Boot Half B.stl]
Print settings:
* Position model on its back (dust boot grooves facing upward)
* Material: PLA+
* 0.4 nozzle
* 0.15 layer height
* 6 walls
* 12 top & bottom layers
* 30% infill, cubic subdivision
* Generate support everywhere
* Skirt
Hardware:
* [3x] - 1/4" x 1/2" cylinder neodymium magnets
Assembly:
# Super glue the two halves together
# Press in the magnets. The magnets should be about flush and in the same plane as the top surface of the boot.
# Glue the magnets in place.
# Install the brushes. No glue is needed. Will need to modify to fit. Clamp to press in bristles in place.
# Drill holes to allow for M3 retaining "pins" to fit in.
== Troubleshooting ==
|