CNC Router: Difference between revisions
Line 53: | Line 53: | ||
[https://drive.google.com/file/d/1hwypOCyQ11mNdx32k812W3lDYDm5G8pF/view?usp=sharing FCFL's CAMaster WinCNC post processor for Fusion 360] (automatic tool change disabled) |
[https://drive.google.com/file/d/1hwypOCyQ11mNdx32k812W3lDYDm5G8pF/view?usp=sharing FCFL's CAMaster WinCNC post processor for Fusion 360] (automatic tool change disabled) |
||
[https://drive.google.com/file/d/1a-r5jTKB3JZiiIAkJPnK2pdN5YytItpi/view?usp=sharing FCFL CNC Router Tool Library for Fusion 360] |
|||
== Getting Started == |
== Getting Started == |
Revision as of 06:56, 28 April 2022
Our woodshop is home to a CAMaster Stinger I CNC router that is able to cut wood, plastics, and certain metals.
Certification
The CNC Basic Use & Safey class is a required certification to use this machine.
CAMaster Stinger I CNC Router
Work Dimensions | Width, X | 635 mm (25 in) |
---|---|---|
Length, Y | 914.4 mm (36 in) | |
Height, Z | 127 mm (5 in) | |
Spindle Power | 1.7kW (2.28 HP) | |
Max RPM | 18,000 | |
Collet Type | ER25 | |
Max Rapid Speed | 15240 mm/min (600 in/min) | |
Max Cut Speed | 8890 mm/min (350 in/min) | |
Repeatability | ±0.0254 mm (±0.001 in) |
Reference Material
CAMaster WinCNC Machine Controller Software
VCarve Pro Makerspace ID: 39330-F4690-16995-07DC5-70AEA-01778-91E18
FCFL References
FCFL's CAMaster WinCNC post processor for Fusion 360 (automatic tool change disabled)
FCFL CNC Router Tool Library for Fusion 360
Getting Started
The CNC is one of our more dangerous pieces of equipment. It can be a VERY energetic machine and cause flying metal if improperly configured possibly causing harm to the machine and humans nearby.
Do not use the CNC if you "think" you know how to use it. You need to know how to use it. Any other certified member should be willing to help out if any questions arise.
Safety
Standard Disclaimers:
- Don't be inebriated
- No loose items
- Standard safety gear (safety glasses)
- Tie back hair
- Don't be stupid
You should sign up for a reservation on CiviCRM before using the tool
Before Operating the CNC
Before doing anything, know exactly where the Emergency Stop button is. It is the large red button on the front left side of the machine.
If you press it, you can confirm it worked by reading the code on the spindle rpm controller on the bottom right of the front of the machine which should be displaying 'ER'
You must fully power cycle the CNC and reset the switch (twist) to use the CNC
Win CNC Control Software
Keyboard Controls
Z = page up/ page down, X,Y: arrow keys (labeled on keyboard)
FAQ
Stopping CNC From Software
Emergency Stop (?): Press “Esc” key. Must reload file to start again.
Pause job: Click pause (“||”) in top menu bar.
CNC Won't Start
Check that the Emergency Stop Button is not depressed. Twist to reset position
Can I do a full cut through?
Yes, though you need a sacrificial piece under your main piece. The spoilboard is technically a wear item but cut through massively decrease useful lifetime.
Coordinates
Red = Machine coordinates
Green = Local coordinates
Blue = (only for Z) top-down perspective. Zero at limit switch.
Creating The Cut Files
CAM jobs must use inches.
Using VCarve Pro
We have a Vcarve Pro Makerspace license and you can use it to prepare VCarve files (.tap) on your computer.
You can use Fusion360 to make the files, but we generally recommend testing it in the VCarve application since we have sometimes noticed strangeness with Fusion360 files. (Out of place parts etc etc)
Post-processing
Use 'in' post-processor. Should already be set in VCarve.
Preparing the Cut
Pre-Check
Inspect the machine and bed for any debris, especially the ball screw
Check that the hose in the compressor is attached to the CNC air assist connection
Turn on the air compressor (push red toggle switch backward).
Adjust compressor to provide 60-80lbs pressure to CNC (it has its own pressure regulator).
Turn on the Vacuum
Warm Up Procedure
Note: Spindle RPM DRO in thousands of RPM
1. Remove collet from spindle and set aside.
2. Warm up spindle bearing using the speed control dial on front right of CNC router. This is required for the longevity of the spindle bearings.
- Step 1: 5k RPM for 5 mins
- Step 2: 10k RPM for 5 mins
- Step 3: 18k RPM for 5 mins
Alternate Spinup: To warm up spindle, dial in half-speed (9), click Spindle and run two minutes; then dial in 18 and run two minutes, then click spindle to turn off.
Calibration
In CAMaster:
Zeroing Procedure
IMPORTANT NOTE: Must set Z zero at bottom of work if using multiple tools. You can set Z zero at top of work if just engraving with one tool.
1. Check the bed is clear of debris or obstruction
2. Click “Initialize”. This will home the Z, and X-Y axes
3. Insert tool #1.
4. Remove dust collector boot from spindle.
5. Click “Measure tool” (at corner of screen).
6. Connect touch plate and Click “Touch Top”.
7. Click “Laser On” (it’s not perfect rn, needs alignment).
8. Click “Laser X0 Y0”.
Temp notes Ignore Type G92 to clear any stored settings
Insert first tool of job in collet
Turn on laser using ‘Laser On/Off’.
Position X & Y to desired zero point, click ‘Laser X0Y0’
For ‘Z0 at top’ jobs, plug in touch plate, position under tool and Press “Touch Top” button.
For ‘Z0 at bottom’ jobs, Make sure no local Z is set. T codes in job trigger measure tool. Ensure job rapids clear all clamps.
Securing the Stock
Spoilboard has 1/4”-20 threaded sockets for clamping and otherwise securing your piece.
Bolts:
- Machine screws, Phillips flat head, Stainless steel 18-8, 1/4"-20 x 1"
- Machine screws, Phillips flat head, Stainless steel 18-8, 1/4"-20 x 1-1/2"
- Machine screws, Phillips flat head, Stainless steel 18-8, 1/4"-20 x 2"
Flat Washers:
T-Nuts: For spoil board.
- T-Nuts, Stainless steel 18-8, 1/4"-20 x 5/16" - 115 needed.
You can either use clamps, or preferably screw the piece down. Either directly, or using waste parts to secure it on the edges.
The Cut
Spindle speeds typically 7k-18k rpm. Typical feedrate ~200ipm.
Calculate feedrate with this formula: Feedrate = (Chipload) x (Cutter Diameter) x (Number of Flutes) x (Spindle Speed)
Better to begin at lowest end of recommended feedrate and increase feed up to:
- the finish deteriorates because of vibration of the cutting tool
- tight radii causes the machine to adjust to a slower speed
- the part moves
Upcut vs Downcut vs Compression Bits: To be written...
Make sure Turn on dust collector before cutting.
Maintenance
Greasing Parts
Replacing the Spoilboard
Compressor/Air Tank Draining
Troubleshooting
Spindle wont start
Hit reset button on spindle controller console. Check that speed control knob is fully clockwise
WinCNC Wont Start
Restart PC. Pray to whatever deity(ies) you may believe in
Pinned Items from Slack #cnc and Other References
Comprehensive Guide to Router Bits
Harvey Tools General Machining Guidelines
VCarvePro (Windows) FatCatFabLab serial: 39330-F4690-16995-07DC5-70AEA-01778-91E18